Embroidering the Embossed Towel


FinishedTowelEmbroidered towels look great in your powder room or bathroom. They also make great gifts for showers, weddings, house warmings, birthdays, or the holidays. It is easy to embroider the towel if you follow a few easy steps.

Look at your towel. Most towels have a band on the front, and some on both front and back. Usually, there is a label on the back of the towel. Your embroidery should be on the front.

For the best results always mark where you want the embroidery to be placed. I learned that eyeballing the placement never works.  The embossed embroidery design is 4″ x 4 1/2″.  Always use the smallest hoop

1. Measure the width of your towel. My towel is 15 1/2″ wide.

measure 2. The bottom of the design is placed 1/2″ – 1″ about the band, if the towel has one. If the towel does not have a band, place the design about 3″ from the bottom of the towel. Since my design is 4 1/2″ high, the middle of the design is 2 1/4″. My design is 1/2″ above the band. Measure 2 3/4″ above the band and mark with a + or use a positioning sticker.  You can mark your placement with a water soluble pen, air erasable pen or friXion pen.  The center of the + is where the needle should penetrate the towel before starting the embroidery; the + lines show vertical and horizontal alignment. Note: Don’t use a water soluble pen, if you use heat n’ gone topping. The use of an iron will permanently set the mark.

center

 

3. Always use the smallest possible hoop for your embroidery. It saves on stabilizer but more importantly, provides better stability during embroidery.  I like to use Floriani Stitch and Wash Tearaway. Cut a piece of stabilizer about 1″ larger that you hoop. Place it in the hoop and tighten the hoop screws so that it is taught. There is no need to over tighten the screw.

InHoop4. Lightly spray the stabilizer with temporary spray adhesive. I like 505 because it does not leave a sticky residue on my needle when embroidering. Stray by putting your hoop into a box or trash can to minimize spraying all over the place.

5. Select a thread color similar to your towel. Wind a bobbin with the same thread so the back of your towel is not covered with white bobbin thread. If you embroidery machine uses a different bobbin case for embroidery change your bobbin case. Insert the bobbin and thread your machine.

6. Turn on your embroidery machine and open your design.

7. Place the towel on the hoop. Use the template that came with your embroidery machine to position your towel in the middle of the hoop. Reposition the towel if necessary.

templatem

7. Place the hoop on the embroidery machine. The design should be near the center of your hoop. Move the design around as needed. Lower the needle so that it penetrates the embroidery mark or sticker. Raise the needle.

needledown

8. Remove the position sticker if you used one. Place a water soluble topping or heat n’ gone on the embroidery area. Use a piece of Floriani Pink Embroidery Tape to hold the topping in place during embroidery. I sometimes use blue painters tape to hold the topping in place.

topping

9. Embroider the design. Remove the towel from the hoop. Tearaway as much stabilizer from the back as possible. The remaining will wash out. Pick water soluble stabilizer from the top. Use a spray bottle to remove stubborn parts. Use an iron to remove heat n’ gone.

Enjoy your towel!

This entry was posted in Home Decor, Machine Embroidery FYI, Project Tutorials, Uncategorized on by .

About Designs by Marje

Marje is an avid sewing and machine embroidery enthusiast. She started sewing as a teenager and has continued sewing through the years. About 15 years ago she purchased her first embroidery machine and software. She was hooked! Marje previously worked in the information technology field for 35 years which has given her a solid background in computer technology and software. She has been teaching sewing machine guide classes and embroidery software classes for more than 12 years. Her resume includes teaching at a number of local sewing machine shops and at the Husqvarna Viking Annual Dealer Convention where she taught classes on Embroidery software to dealers and their associates. By attending her sewing, machine embroidery and embroidery software classes you will expand your knowledge in sewing, embroidery, software, and computer technology.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s